Wrought Aluminum 5305

Representative aluminum raw/semi-finished material photo; exact grade not verified

Image Credit: alucoilmetal.com

Wrought Aluminum 5305 (AA 5305) is a registered low-magnesium aluminum alloy in the 5xxx series. Its tightly restricted silicon, iron, zinc, and titanium limits, together with 0.7–1.1% magnesium, distinguish it from more broadly alloyed general-purpose Al-Mg grades. The designation is associated with clean, low-alloy wrought feedstock and is listed by a materials portal for rounds, round blanks, and extrusion slugs, including general-use and food-contact applications. As a non-heat-treatable alloy, its practical strength is developed principally through cold work rather than precipitation heat treatment.

Chemical Composition (wt.%)
Chemical Composition wt.%
ElementMinMax
Silicon—0.08
Iron—0.08
Manganese—0.03
Magnesium0.71.1
Zinc—0.05
Titanium—0.02
Others, each—0.02
AluminumRemainder
Composition notes
  • Silicon: Maximum
  • Iron: Maximum
  • Manganese: Maximum
  • Magnesium: Range
  • Zinc: Maximum
  • Titanium: Maximum
  • Others, each: Maximum individual unspecified element
  • Aluminum: Balance

Registered composition limits are percent by mass from the Aluminum Association designation table. Blank entries in the registered row are not reported as zero and are omitted here. Aluminum is the remainder. The source lists an individual “Others” limit of 0.02%; no “Others Total” limit is displayed for 5305.

The Aluminum Association reports the following calculated nominal density for alloy 5305. No grade-specific tensile, yield, thermal-conductivity, or electrical-property values were available in the supplied sources; such values depend on the delivered product form and temper.

Use the button to switch between Metric and US Customary units.

Table of Wrought Aluminum 5305 Properties
Table of Wrought Aluminum 5305 Properties
Physical PropertiesMetric
Density (calculated nominal)
0.097 lb/in³2.68 g/cm³
Density (calculated nominal)
2.69 × 10³ kg/m³
Test conditions & data notes
  • Density (calculated nominal): Calculated nominal density for active wrought alloy 5305
  • Density (calculated nominal): Calculated nominal density for active wrought alloy 5305

Material Conditions & Tempers

5305 is a non-heat-treatable Al-Mg alloy. It may be supplied annealed or strain-hardened, with the actual temper, dimensions, and mechanical-property requirements established by the applicable product specification and supplier certification. The supplied sources do not provide 5305-specific strength tables.

ConditionDescriptionNotes
OAnnealed condition, selected where maximum softness and forming latitude are required.Mechanical values depend on product form and are not reported in the supplied grade-specific sources.
H1x / H2xStrain-hardened conditions used when greater strength than annealed material is needed; the final digit denotes the degree of hardening.Availability and property limits must be confirmed for the ordered 5305 product form.

Advantages & Limitations

AdvantagesLimitations
  • Low magnesium content provides an Al-Mg chemistry while retaining a density of 2.69 × 10³ kg/m³ as calculated by the Aluminum Association.
  • Very low silicon and iron limits support a clean, tightly controlled composition compared with many general commercial aluminum grades.
  • Non-heat-treatable temper response allows strength adjustment through cold work without relying on solution treatment and artificial aging.
  • The material portal identifies EN AW-5305 for rounds, round blanks, and extrusion slugs, indicating relevance to semi-finished feedstock applications.
  • The Applus+ listing identifies the grade as suitable for food-contact use; final suitability remains dependent on the supplied product, processing route, and applicable regulation.
  • 5305 is not a precipitation-hardening alloy; it cannot obtain the heat-treatment strength levels associated with 6xxx or 7xxx alloys.
  • No 5305-specific mechanical-property data were supplied, so design strength must be taken from the governing product standard and the mill certificate for the exact temper and dimensions.
  • The narrow impurity limits require disciplined melt control and segregation of scrap or return metal during production.
  • A low-magnesium grade should not be assumed to offer the strength or marine-service performance of higher-magnesium 5xxx alloys such as 5083 or 5086.
  • Welding procedure qualification and corrosion evaluation remain necessary for the actual joint design and service environment.

Processing & Fabrication

ProcessDescription
Cold formingUse the annealed condition when substantial shaping is required. If a strain-hardened temper is specified, account for its reduced forming margin and consider intermediate annealing where the product route permits.
Extrusion feedstock preparationThe available materials listing specifically identifies rounds, round blanks, and extrusion slugs. Maintain composition segregation and clean handling so that the low Si, Fe, Zn, and Ti limits are not compromised.
WeldingAl-Mg alloys are generally weldable by common aluminum fusion-welding methods, but filler selection, joint preparation, shielding, and qualification should be established for the exact 5305 temper and service requirements.
Finishing and cleaningUse aluminum-compatible cleaning and surface-treatment sequences. For food-contact components, validate cleaning residues, coating systems, and compliance against the applicable regional food-contact rules.

Applications

Available source information points to semi-finished round products rather than a broad structural-product database. Accordingly, 5305 is most relevant where controlled low-magnesium Al-Mg composition and wrought round or slug feedstock are more important than high structural strength.

  • Extrusion slugs and round blanks: The Applus+ material listing specifically identifies rounds, round blanks, and slugs for extrusion made from semi-finished products.
  • General-purpose formed aluminum components: The low-alloy 5xxx chemistry and availability in annealed or strain-hardened conditions can suit parts that prioritize formability and low mass over heat-treatable-alloy strength.
  • Food-contact semi-finished products: The cited materials listing describes EN AW-5305 as suitable for food contact; the finished item still requires application-specific regulatory and process validation.
  • Low-impurity aluminum-magnesium feedstock: The registered limits tightly control silicon, iron, zinc, titanium, and individual unspecified elements, making composition control a principal selection factor.

Standards & Designations

DesignationValueDescription
Aluminum Association International Alloy Designation System5305Active registered wrought aluminum alloy designation; the Aluminum Association table records registration in 1990 by EAA.
EN designationEN AW-5305Shown in the Applus+ datasheet title.
EN chemical nameEN AW-Al 99.85Mg1Shown in the Applus+ datasheet title.
Common designationAA 5305Wrought Aluminum 5305 is identified as AA 5305 in the material record.

Frequently Asked Questions

What is the magnesium content of wrought aluminum 5305?

The registered 5305 composition specifies 0.7–1.1% magnesium by mass. It is therefore a low-magnesium member of the wrought 5xxx aluminum series.

Can aluminum 5305 be strengthened by heat treatment?

No. Like other conventional Al-Mg 5xxx alloys, 5305 is non-heat-treatable for strengthening. Its usable strength is principally set by the supplied strain-hardened or annealed temper, product form, and dimensions.

Is 5305 the same as EN AW-5305 / Al 99.85Mg1?

The supplied Applus+ datasheet identifies its material as “EN AW-5305; EN AW-Al 99.85Mg1.” The Aluminum Association separately lists 5305 as an active registered wrought designation. Purchase documentation should still state the required standard, temper, form, and certification requirements.

References & Data Notes

  1. (n.d.). The Aluminum Association, International Alloy Designations and Chemical Composition Limits for Wrought Aluminum and Wrought Aluminum Alloys, revised December 2025. https://www.aluminum.org/sites/default/files/2026-01/Teal%20Sheets%20December%202025.pdf
  2. (n.d.). Applus+ Materials Portal: EN AW-5305; EN AW-Al 99.85Mg1 Material Datasheet. https://www.appluslaboratories.com/materials-portal/datasheet/en-aw-5305-en-aw-al-99-85mg1/DefaultItemKey_a2JfbWxpbmUtMzUwNS0x

Composition and calculated nominal density are source-reported for registered wrought alloy 5305. Mechanical, thermal, and electrical values were not added because the supplied sources do not provide verified numerical data for the exact grade, temper, and product form.